Soloy Helicopters Airbus AS350 B3 accident
Airbus AS350 B3 · Accident: collision during takeoff/landing
From Pogo Mine Airstrip (76AK) to Pogo Mine Airstrip (76AK)
Event
- NTSB case
- ANC17CA041
- Event typeAccident: someone killed or seriously injured, or the aircraft substantially damaged (NTSB definition). Incident: an occurrence that affected or could have affected safety, short of that. Glossary
- Accident
- InvestigationHow far the investigation had got when the record was published: preliminary, ongoing, final or completed. Unknown where the source does not say. Glossary
- Completed
- API-reported fatalities
- 0 · all aircraft and ground
- Ground fatalities
- Unknown
- OperationWhat kind of flying it was, grouped by the rules it flew under: airline (US Part 121), air taxi and commuter (Part 135), general aviation (Part 91 and similar), military or government. Glossary
- Charter & commuter
- WeatherVisual meteorological conditions (VMC): good enough to fly by looking outside. Instrument conditions (IMC): cloud or low visibility, flying by instruments. Glossary
- Visual Meteorological Cond
Airbus AS350 B3
- Aircraft type
- Airbus AS350
- Category
- Helicopter
- RegistrationThe aircraft's tail number, such as N12345 or G-ABCD. Registrations are reissued, so the same one years apart can be a different aircraft. Glossary
- N351SH
- Operator
- Soloy Helicopters
- Onboard fatalities
- Unknown
- Route
- From Pogo Mine Airstrip (76AK), Delta Junction, AKTo Pogo Mine Airstrip (76AK), Delta Junction, AK
- Aircraft age
- About 9 years (built 2008)
- Flight rulesThe regulations the flight operated under: in the US, Part 91 (general aviation), Part 121 (airlines), Part 135 (air taxi and commuter) and others; for flights abroad, the NTSB's coarser commercial or non-commercial code. Glossary
- Part 135: Air Taxi & Commuter
- Phase of flightThe stage of the flight when things started to go wrong: standing, taxi, takeoff, initial climb, en route, maneuvering, approach or landing. Glossary
- Landing
- Defining eventThe single coded event the NTSB judges best describes what happened (records from 2008 on). Older records name the first occurrence in the sequence instead. Glossary
- Collision during takeoff/landing
- DamageDestroyed: beyond practical repair. Substantial: damage that affects the structure, performance or handling and normally needs major repair. Minor: less than that. Glossary
- Substantial
Cause areas
- Environmental issues › Physical environment
- Personnel issues › Psychological
Approximate · Coordinates as recorded by the NTSB; no uncertainty radius is established.
NTSB narrative
The helicopter pilot reported that he was transporting a passenger to a remote drilling site where a tracked drilling unit was stationed. He reported that he landed into the wind, which necessitated descending over bordering trees into the drilling site. The helicopter touched down on the dirt, and upon lowering the collective, he reported that he heard a "bang," and the helicopter slowly started to "pick up a ground wobble." The pilot shut down the helicopter, and both occupants exited without further incident.
A postaccident inspection revealed that the blue and red main rotor blades sustained substantial damage from impacting a black 1.5-inch steel frame attached to the tracked drilling unit, which is used to mount a canvas weather shelter for the drilling crews. The pilot reported that the steel frame was not visible to him from above as he was descending into the drilling site. The pilot further reported that he had made multiple landings at the drilling site in the past 3 months and that, with the previous landings, he had landed farther past the tracked drilling unit, and the steel frame was always behind the helicopter.
The pilot reported that there were no preimpact mechanical failures or malfunctions with the airframe or engine that would have precluded normal operation.
The Federal Aviation Administration Helicopter Flying Handbook (FAA-H-8083-21A, 2012) discusses high and low reconnaissance procedures and states, in part:
The purpose of conducting a high reconnaissance is to determine direction and speed of the wind, a touchdown point, suitability of the landing area, approach and departure axes, and obstacles for both the approach and departure.
A low reconnaissance is accomplished during the approach to the landing area. When flying the approach, verify what was observed in the high reconnaissance, and check for anything new that may have been missed at a higher altitude, such as wires and their supporting structures (poles, towers, etc.), slopes, and small crevices.
Probable cause
The pilot’s failure to maintain clearance from a steel frame attached to a tracked drilling unit. Contributing to the accident was the pilot’s failure to visually identify the steel frame during the reconnaissance process.
Verbatim NTSB analysis and probable cause from the NTSB dataset
Sources
NTSB record ANC17CA041
- Event ID
- 20170807X70934
- Case number
- ANC17CA041
- Dataset
- full-current
- Source SHA-256
- 5cf380f0061817c0331a6b2d8cc7e0ee3a79bea469a1001dc5c10e56f35f5ab3
Source notes (4)
- Unreviewed is an editorial label, not an investigation status. API-sourced is not report-checked or human-reviewed. Explicit event totals are used without summing aircraft injury tables; onboard allocation is withheld. Unknown values remain unknown. The operation category is mapped from the NTSB-reported FAR part and has not been reviewed.
- Filled from the NTSB case API where the bulk record had no value: investigation status. Values present in the bulk record are kept.
- The date is the local date, which is the same as the UTC date the NTSB stores.
- API snapshot SHA-256: 78d2c661deec5e458150556333e5c57d6c31bc50adc16cda4acd4dd68b490b86; retrieved 2026-09-16T05:40:35.894Z.